home products services photos contacts

Catalogue of products.

Name

Destination

Drawing
Small-sized rod preventer 3-6221

ASSIGNING:
The preventer is designed for sealing a pipe duct of tubings at descent and ascent of rods a cable, geophysical, as well as for sealing a pipe duct of tubing at absence of rods (after substitution of pipe rams (on blind ones).

s10
Small-sized rod coaxial preventer 23-6221

ASSIGNING:
The preventer is designed for sealing a pipe duct of tubings at descent and ascent of rods, as well as for sealing a pipe duct of tubings by a spheric member (trunk . at absence of rods.
2 may be utilised as the wellhead automatic shutdown cock used for operative overlapping and sealing of a pipe channel at breakaway of a polished rod of of a under condition of installation of the drive, allowing to turn trunk of a preventer on 90 grades by analogy with 1 (look the wellhead shutdown cock 1-62x14.)

s10
Small-sized tube preventer of 1 serial

ASSIGNING:
The preventer of 1 serial (-12521, -15621) is designed for sealing a well head by pipe (if there is in a well), by blinds (at absence of in a well) and pipe - cable rams (at presence in a well of a tube and a cable of ).
Sealing is provided after preset of the corresponding rams Installation of cable dismountable sealer ( ) in the upper fitting pipe of the preventer (-12521, -15621 if there is a thread lock ring groove) allows to seal a geophysical cable on hole mouth. Updates of preventers 1 it is released with the conditional pass of 80, 125, 156 mm and working pressure 21 MPa.

s10
Small-sized tube preventer of 2 serial

ASSIGNING:
The preventer of 2 serial is designed for sealing a mouth wells with pipe rams of the upper channel at availability of in a well and blind rams of the low channel at absence of as well as allows to seal a different diameter (sealing of a mouth at absence of is carried out with pipe rams enclosed on a branch pipe with the ball cock).
Sealing of tube and cable is madewith pipe-cable rams of the upper channel (it is indispensable preliminary substitution of pipe rams on pipe-cable). Updates of preventers 2 are released with the conditional pass of 125 and 156 mm and operating pressure 21 MPa.

s10
Preventer with ovality rams of serial

ASSIGNING:
The preventer of serial is designed for sealing hole mouth by tube rams (at availability of in a well) and blind ones (at absence of in a well).
Sealing is provided after preliminary installation of the corresponding rams.
Updates of preventers of are issued with the conditional pass of 160 both 180 mm and working pressure 21 and 35 MPa.

s10
Preventer with ovality rams of 2 serial

ASSIGNING:
The preventer of PP2 serial is designed for sealing hole mouths with pipe rams of the upper channel at corresponding in a well and blind rams of the lower channel at absence , as well as allows to seal a different diameter (sealing of a mouth at absence is carried out by pipe rams , enclosed on a pipe branch with the ball cock).
Updates of preventers PP2 are issued with the conditional pass of 160 both 180 mm and working pressure 21 and 35 MPa.

s10
Dual preventer with plane cutters of 2 serial

ASSIGNING:
The preventer of 2 serial is designed for sealing of hole mouths with pipe rams of the upper channel at availability of in a well and rams of the lower channel at absence of , as well as allows to seal a different diameter (sealing of a mouth at absence is carried out with pipe rams , enclosed on a pipe branch with the ball cock).
Updates of preventer 2 :
2. 1 - with two flanges;
2. 2 - with two leaning butt ends;
2. 3 - with the upper flange and lower leaning butt end;
2. 4 - with the lower flange and upper leaning butt end.

s10
Small-sized combined preventer of serial

ASSIGNING:
The preventer of serial is designed for sealing a mouth of wells with pipe rams at availability of in a well and with a slide gate located behind tube rams , at absence of .
The preventer of serial may be utilised in quality of perforating valves with a view to sealings of hole mouth at conducting of perforating operations.
Updates of a preventer :
1 - with two flanges:
2 - with two leaning butt ends;
4 - with the lower flange and upper leaning butt end.

s10
Small-sized tube unloaded preventer of serial

ASSIGNING:
The preventer of PTMR serial is designed for sealing of hole mouths tube (at availability of in a well), blind rams (at absence of in a well).
Sealing is provided after preliminary installations of the corresponding rams . In the upper branch pipe of preventer may be installed the centralizer of , serving for supply of an alignment of drained off (uplifted) string of and a bore of preventer in view to cancelings abrading and percussive affecting of string on a preventer, and supporting reliable gripping of by rams.

s10
Cable demountable sealer 1

ASSIGNING:
Cable demountable sealer is installed in a thread part (at availability) of preventers of -125x21 and -156x21 seriasl and is designed for:
- sealings of hole mouth with the dropped geophysical cable at perforated and geophysical operations;
- sealing of hole mouth at absence of cable;
- use of GRK allows to refuse from perforating valve and to save a cable from cutting off at initiation ingresses of oil.

s10
Cable preventer

ASSIGNING:
Cable preventer is designed for fixation and holdings of a demountable cable sealer 1 in a site. The preventer is designed on the base of 1, is a body which one may be installed on a flange of control head.

s10
Complex of the process equipment and 1--- 10 units
Pipe hookup of a mouth by operation with and 1

ASSIGNING:
Complex of the process equipment & 1 is designed for :
- sealings of hole mouth with dropped string of and cable of at technological interruptions;
- sealings of hole mouth with dropped geophysical cable at conducting of perforated operations;
- sealings of hole mouth with dropped leading tube at drilling over of cement sockets and sandy corks;
- sealings of hole mouth with dropped string of at washover;
- centerings and clearing of drained off (uplifted) string at conducting of technological operations.

2 units
Wedge revolving controlled grip 1--- s10
Wellhead sealer of serial

ASSIGNING:
Wellhead sealer is designed for sealing of round tube if there is pressure on a mouth.
The sealer enables axled movement of a tube, its rotaryl motiont, dragging of coupling s through sealing hermetically element under pressure top-down and from below up.
Magnitudes of working pressures at drawing through depend from diameter of coupling s and tubes, and as from update of a sealer. It is used at a thaw of wells, development of wells after GRP and at washover of wells with building-up.

s10
Pipe hookup of a mouth 1-95300 and .

Wedge revolving controlled grip 1-95300

Wellhead sealer of serial

ASSIGNING:
Wedge revolving universal grip 1-95300 is designed for holding a tube of from pushing by pressure from a well. It is applied at thaw of hydrated corks or the frozen wells and at lowering / rise of tubes under pressure. Use is possible at rise of the instrument after a fluid fracturing of a bench (in kit with ).

s10

ASSIGNING:
Wellhead sealer is designed for sealing of round tube if there is pressure on a mouth. The sealer enables axled movement of a tube, its rotaryl motiont, dragging of coupling s through sealing hermetically element under pressure top-down and from below up.
Magnitudes of working pressures at drawing through depend from diameter of coupling s and tubes, and as from update of a sealer.
It is used at a thaw of wells, development of wells after and at washover of wells with building-up.

Wellhead rotary sealer 1-8010

ASSIGNING:
Wellhead rotary sealer is designed for sealing of leading tube if there is pressure on a mouth at its rotating and axled movement.

s10
Pipe hookup of a mouth well 1-8010

ASSIGNING:
The given arrangement is designed for sealing of leading tubes if there is pressure on a mouth at its rotating and axled movement. It is applied at drilling over of cement corks, fishing (emergency) operations. For rotating of leading tube the rotor is used.

s10
Complex of ground-level equipment for swabbings of wells.--- 9 units
Layout of ground equipment complex for swabbing of wells.

ASSIGNING:
Complex of ground equipment for swabbing of wells is designed for safe influx of inflow of a liquid at development of oil-wells by method of swabbings at a tight mouth.
KNOS provides fluid influx from a bench without impairment of collecting properties of a bottomhole zone of a well.

s10
Downhole equipment for swabbings 62---8 units
Layout of downhole for swabbing of 62

ASSIGNING:
The swab string is designed for safe challenge of fluid influx at development of oil-wells by method of swabbings at a tight mouth.
KS provides fluid influx from a bench without impairment of collecting properties of a bottomhole zone of well.

s10
Hoisting jack hydraulic 2-100

ASSIGNING:
The hoisting jack hydraulic is recommended to be applied for liquidation of stickings tubing and drill-pipes at a testing, development or repair petroleum and gas wells.

s10
The junk retriever ""

ASSIGNING:
The implosion junk retriever is designed for:
- clearing of a bottom hole of outside subjects, including nonmagnetic, in mass up to 20 kg;
- clearing of "head" of the stuck instrument after milling.

s10
Junk retriever

ASSIGNING:
Junk retriever is designed for :
- catchings of debriss of metallical objects broke up in a well and separate pieces of arms of rock-destroyin instruments (boring heads, milling cutters etc..).

s10
Withdrawing device of a downhole instrument

ASSIGNING:
Withdrawing device of a downhole instrument (ISP) is designed for :
- breakdown elimination bound with sticking in a well bore of geophysical cable or downhole instrument;
- grab of the stuck downhole instrument reeved with thimble and lowered in a well on the load-carrying geophysical cable;
- clamp and shearing of cable.

s10
Wellhead shutoff valve 1-6214

ASSIGNING:
Wellhead shutoff valve is designed for operative blocking and sealing of pipe duct of tubing in case of breakaway of SHSN polished rod at exploitation of wells.

s10
Multifunction valve 2.73

ASSIGNING:
Multifunction valve 2.73 is used in arrangement with installation of electrocentrifugal pump () also provides:
- infill of string at lowering of ;
- pressure test of string upon termination of lowering as the installation of , and a hydrostatic testing unit immediately from wellhead;
- scissoring of an annular space from shank bore of string at start of ;
- warning of a fluid drain from string at emergency stops of ;
- washover of string through an annular space;
- fluid drain from string at rise of (at angle of lean of separate hole sections no more 35o ).

s10
The process equipment for fixing wells 102/146

ASSIGNING:
The process equipment for fixing wells by liners the conditional diameter 102 mm. TOKS 102/146 is applied to improvement of quality of insulation productive of bench from neighboring benches there, where because of very their close location cementation of "liner" without applying the casing wall packer of sufficient insulation does not provide.

s10
The process equipment for fixing wells 102/146-01

ASSIGNING:
The process equipment for fixing wells by liners the conditional diameter 102 mm. TOKS 102/146-01 is applied to prevention of affecting high of flowing pressure on a productive bench at driving of cement slurry in annular space.

s10
The process equipment for fixing wells 102/146--- 6 units
The process equipment for fixing wells 102/146--- 4 units
Wall packer hidromechanical

ASSIGNING:
Wall packer hidromechanical is designed for :
- testing of casing strings and of control head on tightness;
- sealing of benches at a fluid fracturing.

s10
The ball cock of serial

ASSIGNING:
The cocks of KSH serial produced in updates of KSH with a tool-joint thread) and KSH (with thread), are designed for operative blocking and sealing of pipe channel of drilling tool at drilling of petroleum and gas wells, as well as of pipe duct of at conducting of remedial and emergency operations.
Updates of KSHN are designed for operative blocking and sealing on a well head of pipe duct at conducting of remedial and emergency operations. Updates of KSH3 are issued with connecting threads as with right, so and the left-hand direction of coils.

s10
Inverted valve of serial

ASSIGNING:
Valves of KOSH serial, produced in updates of KOSHZ (with a tool-joint thread) and KOSHT (with thread ), are designed for sealing of pipe duct of the well instrument at boring of petroleum and gas wells, and also, at conducting of remedial and emergency operations.
Updates of KOSHZ are issued with connecting threads as with right, so and the left-hand direction of coils.

s10
Subs for drill columns on 7360-82

ASSIGNING:
Subs are designed for joint among themselves parts of drill column and attachment to it of the instrument, applied at well boring.

7 units
Subs for oil-well tubings on 23979-80

ASSIGNING:
Subs are designed for joint among themselves oil-well tubings of different diameters, and also the underground equipment having connecting ends with a tubing thread, used at exploitation of petroleum and gas wells.

5 units
Vibration channel screen .2

ASSIGNING:
The screen is designed for clearing drill fluids at building of petroleum, gas and water wells, as well as at their repair.

s10
Hydroclone installation -30

ASSIGNING:
Hydroclone installation is designed for clearing of drill fluids from fragments of drilled solids the size less than 0.8 mm at building of petroleum, gas and water wells, as well as at their repair.
The construction of installation provides conducting preventive of repair in field conditions.

s10
Vacuum degasser of Skvortsov

ASSIGNING:
Degasser is designed for removals of gas from flushing fluid and drill fluid at boring and repair of petroleum and gas wells.

s10
Paddle-type drilling mud stirrer

ASSIGNING:
It is designed for stirring of drill fluid in accumulative capacitances of circulating systems of drill units.

s10
Vertical slime pump -150

ASSIGNING:
Vertical slime pump is designed for :
- flowing through of household and industrial sewages and other contaminated fluids;
- flowing through of flushing solution applied at well boring:
- feedings of waste flushing solution in hydrocyclone unit for clearing of drilled solids.

s10
Throttle - shut-off device -250; -320

ASSIGNING:
The throttle - shut-off device is designed for:
- triggering of boring pumps in the conditions supporting absence loads on actuating motors;
- smoothly recovery of fluid circulation in a well.

s10
Facilitated sleeves high-pressure

ASSIGNING:
RVD is intend as hoselines for a feed by pressure of drill fluids, mineral and synthetic oils on the petroleum ground chilling water, compressed air, RVD are used at workers temperatures from - 40 up to +100 and temperature ambient air from -50 up to +70. Production differs high quality affirmed the European certificate. RVD with nose-pieces are produced any length according to the nomenclature of customer. All nose-pieces have qualitative antirust coat Fe/Zn.
Service life till 2th years, servicing and recovery of injured sleeves from an import material with certification of commodity.

s10
Underground horizontal drainage Capacities of and type (with a preheater)

ASSIGNING:
Capacitances are designed for residuum discharge of light and dark oil products, oils, condensate, including in a mixture with water from technological webs (pipe lines) and devices in all industries, at the contents of hydrogen sulphide in gas phase no more than 1,8 % volumetric.

s10


    NPO "SibBurMash", Tyumen, +7 345 247 2584   nposbm@tmn.ru


:: Home :: | Products :: | Services :: | Photos :: | Contacts ::

© 2002 NPO" SibBurMash"
    webcom@mail.ru @Mail.ru